Multi-tech-systems MTASR1-100 Uživatelský manuál Strana 174
- Strana / 207
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MTASR1-100 Owner’s Manual
174
9.2.3 Using MultiExpress with MCSI
At this point you have run MCSIWSN according to the procedure in either Section 9.2.1 or 9.2.2. This section
will indicate how to use MultiExpress to connect with the MultiRouter modem. It is assumed that MultiExpress
has been installed on your client PC.
Note: Any LAN network communications software program with a MCSI compatible interface can be used to
establish a session with the MultiRouter modem.
1. If MultiExpress has not been installed, then install it by placing the MultiExpress disk in the floppy drive,
typing MEINSTALL and pressing Enter.
2. Run METERM by typing METERM and pressing Enter. The opening title Screen appears and then the
main screen appears.
3. If the status line at the bottom of your screen indicates COM1 or a connection type other than MCSI.
Then press ALT+L to pop up either the question shown below if a connection was active or the screen
shown in step 4.
4. If a session was active drop the session by selecting "YES" and pressing Enter. The Connection Type
Menu appears.
5. Select MCSI as your connection type by highlighting MCSI and pressing Enter. The following screen
appears.
6. If the MultiRouter is the only communications server on your LAN, you can press F2 to connect to the
MultiRouter modem. The Modem type OUTBOUND/INBOUND screen appears.
- Model MTASR1-100 1
- Single WAN 1
- Multi-Protocol Router 1
- Owner’s Manual 1
- Owner's Manual 2
- 82052804 Revision E 2
- Contents 3
- 1.1 Introduction 8
- 1.2 About This Manual 8
- 1.3 Network Overview 10
- 1.3.1 Packet 11
- 1.3.2 Network Address 12
- 1.4 Typical Applications 14
- 1.4.1 Typical IP Application 14
- 1.4.3 Subscription 16
- 1.4.4 Configuration 17
- 1.5 Specifications 21
- Requirement 21
- 2.1 Introduction 24
- 2.2 Front Panel 24
- 2.3 Back Panel 25
- 2.4 Shunts 26
- Chapter 3 - Installation 27
- 3.1 Introduction 28
- 3.2 Unpacking 28
- 3.3 Installation 29
- 3.4 V.35 Shunt Procedure 30
- 4.1 Introduction 34
- 4.2 Loading Software 34
- 5.1 Introduction 44
- 5.2 Router Configuration 44
- 5.2.1 Setup Menu 44
- 5.2.2 Protocol Stacks 45
- 5.2.3 Device Drivers 45
- 5.2.4 Other Setup 46
- 5.2.5 Actions 46
- Add A New Network 49
- Delete a Network 49
- Save Change 49
- IP General Setup 50
- IP RIP= [enabled 50
- Modify a Network 58
- Remote Port Setup 61
- 5.2.10 WAN Port Setup 63
- Connection Method 64
- Terminal Server 64
- WAN General Setup 65
- WAN Message Printing Control 65
- Script Printing 65
- Modem Control 65
- Modem Type 65
- 5.2.11 Frame Relay Setup 66
- Error Threshold (N392) 67
- Monitored Events Count (N393) 67
- Adding a DLCI 69
- Deleting a DLCI 69
- 5.2.13 Applications Setup 71
- Enable TFTP Server 72
- Enable =[enable I disabled] 73
- Default Logon Screen 73
- 5.2.14 Filtering 74
- ICMP Filtering 77
- IPX Filtering 77
- Default Action 77
- Filtering Entries List 78
- 5.2.15 Diagnostics 80
- EtherNet Port Test 81
- WAN Port Test 81
- WAN Link Test 81
- 5.3 Download Default Setup 82
- 5.4 Download Firmware Update 84
- 5.5 Configuration Port Setup 86
- 5.6 WAN Device Configuration 88
- 5.7 Remote User Data Base 90
- 5.7.1 Add User 91
- 6.1 Introduction 94
- 6.2 Two RouteFinder 94
- MTASR1-100 Owner’s Manual 140
- 7.1 Introduction 148
- Chapter 8 - Router Management 153
- 8.1 Introduction 154
- 8.2.1 View SNMP Parameters 155
- 8.2.2 Set SNMP Parameters 156
- 8.2.4 Refresh SNMP Object 158
- 8.2.6 Property Sheet 159
- 8.2.8 Agent Name Dialog 159
- 8.2.9 Commands 160
- Window menu commands 161
- 8.3 Telnet Management 162
- 8.3.1 Router Configuration 163
- Router Configuration 164
- Applications 166
- WAN Device Configuration 168
- Remote User Database 168
- 9.1 Introduction 170
- 9.2 Installing MCSI 170
- <Line Type> 178
- <SpecificName> 178
- <GeneralName> 178
- <ServerName> 178
- Software 179
- 10.4 Service 195
- 10.5 The Multi-Tech BBS 195
- 10.5.2 To Download a file 195
- 10.6 About CompuServe 196
- 10.7 About the Internet 196
- Appendixes 197
- Appendix A - Cabling Diagrams 198
- Link Cables 199
- Appendix B - Script Language 200
- Script Language Grammar 201
Související produkty a manuály pro Hardware Multi-tech-systems MTASR1-100
Hardware Multi-tech-systems MVPFX2-2 Uživatelský manuál
(193 stránky)
(193 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce